搜索资源列表
shiboqsi
- 虚拟示波器源代码,使用声卡作为输入-virtual oscilloscope source code, the use of audio input
2410DA
- 2410开发板在ADS下的D/A转换测试程序。 运行步骤: 1 打开DA.mcp工程文件 2 运行 3 使用示波器, 连接示波器与开发板上的DA输出和地线, 观察示波器上的变化 文件说明: ad_test.c 开发板初始化文件 ad.c ad实验主程序文件 -2410 ADS development board in the D / A converter testing procedures. Running steps : an open DA.mcp
CVI2
- 利用CVI制作虚拟示波器,比传统示波器更易使用,且可以自己更改功能。-produced using CVI virtual oscilloscope than traditional oscilloscope easier to use, and can change their function.
dailvboshiboqi
- 用NI公司的labview7.1编的一个程序。 本程序可以使用dmm设备采集数据信息,然后通过界面显示(类似示波器),而且,加入了滤波功能,能够自行选择滤波函数,显示滤波后的波形。-using NI companies labview7.1 a series of procedures. This procedure can be used for data acquisition equipment DMM information, then pass the interface show
cosinexp123
- 1.分别利用计算法和查表法产生1000Hz的余弦波信号,并使用示波器观测产生信号的频率和幅度。 2.利用计算法产生其他非正弦类周期信号波形,如周期矩形波、三角波、锯齿波等。-1. Each calculation method and the use of look-up table method have 1000Hz the cosine wave signal, Oscilloscope observation and the use of the generated signal f
SBQ
- 示波器程序 经过调试完全可以运行 供大家交流心得使用-oscilloscope after debugging procedures can run for the exchange of ideas we use
oscape
- c源代码,模拟示波器,开发环境VC6,使用方法见说明
shiboqi
- 2440 44b0上当时 做的示波器使用ucos 与ucgui可以学习一下,包括AD采集现实图形-2440 44b0 oscilloscope ucos ucgui can learn about, if there are problems you can contact me
Oscilloscope-tips
- 收集的一些示波器使用文档和平时使用示波器的心得体会-Collected documents and usually using an oscilloscope oscilloscope experiences
Arduino_oscilloscope
- arduino 示波器,,,使用12864显示屏,祝大家使用愉快-arduino oscilloscope, using 12864 display, I wish you all a happy use
STM8uart
- 此程序是STM8的串口程序,可以作为简单示波器使用,不过波形误差有点大,只作程序研究使用-This program is STM8 serial procedures, it can be used as a simple oscilloscope, waveform error but a little big, the program only for research use
stm32示波器
- stm32示波器主程序,直接下载使用,stm32示波器主程序,直接下载使用,stm32示波器主程序,直接下载使用.
PUB
- 使用xlilnx的vivado为基础环境开发的示波器,采用串口屏显示图像(Using xlilnx vivado based environment development oscilloscope, using serial display images)
数字示波器
- 以STM32F7为平台,使用RGBLCD屏制作的示波器显示界面(Using STM32F7 as the platform, the oscilloscope display interface is made with RGBLCD screen)
程序
- STC12C5A60S2来完成AD采样,量化编码,同时另一路使用滞后比较器计算频率,将被采样信号存储到一个定义的BUFF内,并上传到串口屏,来显示被测波形(STC12C5A60S2 completes the AD sampling and quantization coding, while the other uses the lag comparator to calculate the frequency. The sampled signal is stored in a define
STM32Oscilloscope
- 使用STM32F1系列单片机自带的AD采样功能,DMA传输方式,达到1Mbps采样率。使用并口TFTLCD显示屏显示。(Use AD sampling function that STM32F1 series one-chip computer brings, DMA transmission mode, reach 1Mbps to sample the rate. Use parallel TFTLCD display.)
DSO138
- 基于stm32的示波器,简单好用,配套硬件使用,欢迎大家测试(STM32 based oscilloscope, simple and easy to use, supporting the use of hardware, welcome to test)
串口示波器
- 1. 图形化显示通过Uart 传送上来的采样数据。 2.运行所要求的的基本软硬件环境: 硬件环境 如果您使用的是Windows XP 操作系统,建议使用1G 内存。 运行该程序的计算机必须要有串口或串口转USB 设备。 软件环境 推荐 Windows XP 及以上PC。 64位系统需运行在32 位兼容模式下。 3. 解压软件包即可。
labview简易示波器
- labview 作为一个提供实验运行仿真的软件,适合电子通信等专业的同学使用,优秀的解决了上位机显示的问题
双踪虚拟示波器V1.0
- 示波器的设计,基本上满足日常的使用。可以自动调整频率等功能(Design of Oscilloscope)